Little-wonder Xtra User Manual

LITTLE WONDER®OPERATOR/OWNER MANUALANDSAFETY INSTRUCTIONSforEDGER©2003, LITTLE WONDER, Div. Schiller-Pfeiffer, Inc.Patents Granted in USA and Australi

STARTING AND STOPPING INSTRUCTIONS1. Place lawn edger on ground in horizontal position (see Fig. 9C). Be sure the ignition switch is “ON.” Pull swit

NOTE: A built-in automatic centrifugal clutchdisengages the blade from rotating at engineidle speed. The clutch engages the blade whenthe engine spe

12FIG 12AFIG 1110. Sideways Tilting: Lower either left or right handle to achieve angle cutting (Fig 12D).11. Clutch: The Xtra Edger is equipped with

13FIG 13FIG 15FIG 16FIG 14AIR FILTER MAINTENANCENOTE: Clean and re-oil the air filter every 5hours of operation or daily. The air filter is oneof the

BLADE REPLACEMENT1. Stop engine. Clean area around dust cover and pry out with screwdriver (Fig. 17).2. Through dust cover hole, place 14 mm socket.

CHECK THESPARKPLUGIf engine is low on power, difficult to start or runs poorly at idling speed, check the sparkplug.•Allow engine to cool down.• Remov

PROBLEM CAUSE ACTIONEngine will not run. Ignition switch is “OFF”Empty fuel tankPrimer bulb was not pushed enough timesEngine is floodedTurn switch “O

NOTES17

LITTLE WONDER XTRA EDGER PARTS LIST18KEY # PART # DESCRIPTION1 100500 Screw M5 x 36mm2 100501 Nut Nyloc 5mm3 100100 Ball Bearing 6203RS5 100101 “O” Ri

19LITTLE WONDER XTRA EDGER PARTS BREAKDOWN

CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . .2SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . .2PARTS AND CONTR

20

21LITTLE WONDERXTRA EDGERENGINE PARTSBREAKDOWN

BLADE REPLACEMENT1. Stop engine. Clean area around dust cover andpry out with screwdriver (Fig. 1A).2. Through dust cover hole, place 14mm socket.On

replaces shaft and maintains alignment and contains washers, spacer and gear in housing -DO NOT TURN HOUSING OVER.7. Carefully push new blade shaft up

12. Remove bearing holding screw (A), selftapping clutch housing locating screw (B) and loosen 2 x 5mm screws (C) (see Fig. 6).13. Remove 3 screws, b

REPLACING CLUTCH HOUSING17. To replace clutch housing, remove clutch drum(Fig. 11), tap shaft through housing (Fig. 12)and slide off bearing and clutc

Fit pinion bearing locating screw (43) and leavenut loose (A). Using a screwdriver, lever pinion firmly back to bearing locating screwand tighten nut

HARD STARTINGINSPECTION AND ADJUSTMENTCheck the quantityof fuel in the tank.Remove the plug,attach the cap,ground it and seeif it fires.Is there compr

ENGINE STALLS DURING OPERATIONINSPECTIONPull the recoil starter.Check the quantityof fuel in the tank.PROBLEM & FINDINGSThe motor stops suddenly.P

THE MOTOR RUNS POORLYINSPECTION AND ADJUSTMENTPull the recoil starter and check how the plug sparks.Open the throttle gradually and check the speed.PR

The engine exhaust from this product contains chemicalsknown to the State of California to cause cancer, birth defects or other reproductive harm.13 B

INSUFFICIENT OUTPUTINSPECTIONCheck the spark plug.Check the spark.Check the compression.Check if the engineis overheating.PROBLEM & FINDINGSThe en

31CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSTHE CALIFORNIA AIR RESOURCES BOARD AND LITTLE WONDER ARE PLEASED T

Schiller-Pfeiffer, Inc. warrants each new LittleWonder Xtra Edger for ONE YEAR for residentialuse based on the following terms.This warranty extends t

Little Wonder’s philosophy is to continually improveall of its products. As a result, engineering changesand improvements are made from time to time.

sunny conditions, always wear a hat and longsleeve shirt for protection against skin cancers.Use of a good brand of sunscreen cream is also recommende

SAFE FUELING INSTRUCTIONSRefuel outdoors only. Always switch off theengine and allow it to cool before refueling.Relieve fuel tank pressure by loosen

Check fuel filler cap for leaks at regularintervals. Use the specified spark plug andmake sure it and the ignition lead are alwaysin good condition.R

ASSEMBLING THE XTRA EDGERFUEL MIX AND FUELING1. Fit cross brace (Key #68) to handles (Key #35 & 36) with brace touching the ground. Use 4screws (

Here’s how to mix the oil with the gas:1. Pour 1/2 gallon of the gasoline into a safe one gallon container. Do not mix the fuel and oil in the engine